We have uncovered this article involving A Step-by-Step Guide to Installing a Bathtub below on the web and think it made sense to relate it with you in this article.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably challenging job. If the old bathtub is readily available, the job can relocate rapidly; if you need to open a wall to get rid of the old tub as well as place the new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub as well as set in the new one. Make sure you have qualified on your own for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider utilizing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This short article will help you set up a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools as well as material checklist must make up the following:
- New Bath tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Degree
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipeline Caps
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Safeguard the faucet in position with the supplier provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the supply of water and also inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the tub as well as likewise inspect the overflow outlet as well as the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait up until the bath tub has actually been made use of at least once as this will settle it into its final setting.
Planning for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with dampness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that report about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different web page. Be sure to take the opportunity to share this page if you appreciated it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Maintenance
Comments on “Exactly How to Set up a Tub”